Can I Set Up a Tub Myself? Considerations As Well As Steps
Can I Set Up a Tub Myself? Considerations As Well As Steps
Blog Article
The content listed below involving How to Install a Bathtub is quite stimulating. Check it out for yourself and see what you think of it.
Installing a tub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably hard project. If the old tub is readily available, the job can relocate immediately; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new bathtub, the task is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will need a helper to move out the old tub and also embeded in the brand-new one. See to it you have actually certified on your own for the work and also fit trying it. As opposed to working with a contractor to take control of a halfway-completed task, it is far better to take into consideration utilizing one prior to you start. Possibilities are you may need an expert plumber to make tube connections.
This article will aid you mount a brand-new bath tub in your washroom if you have actually already purchased a new tub and do not require to alter the plan of your previous water system pipes.
Your tools and also product list must make up the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is separate the water system. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The process of removing the existing faucets can be rather problematic as a result of the limited gain access to that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will come from the pipelines. When the supply pipes have actually been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to proceeding to fit the brand-new taps, compare the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly need lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin guaranteeing that the washing machines remain in place in between the tap as well as the sink. Safeguard the tap in position with the manufacturer supplied backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former kind should be attached to the tap finishes initially, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bath tub
Using both wood boards under its feet, put the bath tub in the required setting. The wood boards are useful in equally spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
The following goal is to ensure that the bath tub is leveled all round. This can be achieved by checking the level and also adjusting the feet on the tub till the spirit level checks out degree.
To set up taps, fit the bottom of the outermost flexible tap port to the appropriate supply pipe by making a compression sign up with; after that do the very same for the other faucet.
Switch on the water system and also check all joints and new pipework for leaks as well as tighten them if needed. Load the bath tub and also inspect the overflow electrical outlet and also the regular outlet for leakages.
Finally, repair the bath paneling as explained in the maker's user's manual. Tiling as well as securing around the bath tub needs to wait until the bath tub has been used a minimum of once as this will settle it into its last setting.
Planning for the Installment
To start with, the sustaining structure provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the tap comes with a plastic washer, it is fitted between the bath and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of the two taps using 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be suited its last setting.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to split a rigid seal, creating the water to permeate the wall in between the bath and the tiling, bring about issues with dampness and also possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components and installations. They are offered in tubes and also cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealant can split fairly very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily readily available on the market. It is a good idea to fit the tiles utilizing waterproof or waterproof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that entry about A Step-by-Step Guide to Installing a Bathtub when doing a lookup on the web. Sharing is caring. You won't know, you may just be helping someone out. Thank you for going through it.
Suggested Site
Report this page